THE DETAILS THAT COMPLETE A METAL ROOF
Metal Roof Trims & Flashings: The Complete Waterproof System
A metal roof is not just panels or shingles. The panels cover the open roof areas—but the trims and flashings manage water at every edge, opening and change in direction. Those details are what connect separate pieces of metal into one complete roofing system.
- ✓ Profile-specific trims
- ✓ Custom water-management details
- ✓ Complete Ontario installation planning
FLASHINGS PROTECT.
BUILDING VALUE HOMEOWNERS CAN SEE
The Roof Panels Are Only the Beginning
The middle of a simple roof section is usually the easy part. Installation skill becomes visible where the roof ends, turns, rises, meets a wall or is interrupted by a chimney, skylight or vent.
Every one of those locations interrupts the regular panel field. Water has to be collected, redirected, layered over or safely released from the roof. Correct trims and flashings create those paths while finishing the roof’s appearance.
LOOK BEYOND THE PANELS
A Real Roof Has More Than Four Straight Edges
Each numbered location needs a detail designed for the roof shape, panel profile and direction of water flow.
Simplified illustration. Actual flashing geometry and installation sequences must follow the selected roofing system, roof design and applicable requirements.
WHAT IS METAL ROOF TRIM?
Trim Finishes and Connects
Trim is formed metal used to complete roof edges, corners, ridges, hips and transitions. It helps secure panel ends, cover cut edges, create finished lines and connect the panel field to the surrounding roof assembly.
- Eave and starter trim
- Rake and gable trim
- Ridge and hip caps
- Closures and cover pieces
- Transition and end-wall trim
WHAT IS METAL ROOF FLASHING?
Flashing Redirects Water
Flashing is shaped and layered to collect or redirect water where panels alone cannot complete the drainage path. It protects intersections, penetrations and locations where water becomes concentrated.
- Open or closed valleys
- Chimney and masonry flashing
- Skylight connections
- Wall and dormer flashing
- Pipe, vent and curb details
THE COMPLETE DETAIL PACKAGE
What Each Trim and Flashing Has to Do
Every component has its own job. Missing one can interrupt the planned water path.
Eave & Starter Trim
Begins the panel system at the lower roof edge and connects roofing, underlayment, fascia and drainage.
Rake & Gable Trim
Finishes sloped roof edges while resisting wind-driven rain and protecting exposed panel ends.
Valley Flashing
Creates a supported channel where two roof slopes collect and concentrate water, snow and debris.
Ridge & Hip Caps
Close upper panel intersections while coordinating locks, closures and any designed ventilation.
Sidewall Flashing
Directs water where a sloped roof edge runs beside a wall, dormer or vertical surface.
Headwall Flashing
Manages runoff where the upper end of a roof slope terminates against a wall.
Chimney Flashing
Combines lower, side and upper details around masonry; wider chimneys may require a cricket or diverter.
Skylight Flashing
Connects the roof profile to the skylight curb or manufacturer-approved flashing kit.
Pipe & Vent Flashing
Seals and sheds water around plumbing stacks, exhaust vents and other roof penetrations.
Transition Flashing
Connects panels where roof slope, direction, height or material changes.
Closures & Screens
Close profile-shaped gaps while supporting ventilation and helping control wind, water and pest access.
Custom Cover Flashing
Finishes project-specific intersections that cannot be handled by a standard stock trim alone.
FOLLOW THE WATER
Good Flashing Creates a Continuous Drainage Path
Water should move down and away across overlapping layers without relying on a bead of sealant as the only defence.
Collect
Receive water from the panel field or surrounding roof area.
Redirect
Turn runoff away from walls, openings and vulnerable joints.
Overlap
Layer components so gravity keeps water moving over—not behind—the next detail.
Drain
Release water safely toward the eaves, gutters or designed drainage route.
SEALANT IS A COMPONENT—NOT THE DESIGN
Caulking Alone Does Not Make Flashing
Compatible sealants and tapes can be important at specified joints, laps and closures. They should support correctly shaped metal—not replace it.
A detail that depends on surface caulking alone can become vulnerable as the roof moves, temperatures change and materials age. Proper flashing uses shape, slope, overlap and drainage first, then approved sealant where the system requires it.
THE ACTUAL ROOF SETS THE SCOPE
Standard Trims Meet Custom Buildings
Homes are rarely perfectly square, straight or identical. Older additions, settled framing, masonry, custom dormers and previous alterations can require project-specific measurements and formed metal.
- ✓ Field-verified angles and dimensions
- ✓ Profile-compatible bends and returns
- ✓ Correct metal, coating and colour
- ✓ Planned laps, hems, kick-outs and end conditions
- ✓ Connections coordinated with siding, masonry and gutters
BENEATH THE METAL
Underlayment Is Secondary Protection
Compatible underlayment and ice protection add an important secondary layer beneath the metal roof. T